Salomon Ski Bindings Installation

Salomon offers hundreds of different types of ski bindings. Installing a proper binding depends on the type of skiing, style, tendencies, size and the speed of the skier. Given the inherent danger of installing one's own bindings, installation should only be undertaken by experienced and knowledgeable skiers who are familiar with their personal approach to skiing and all of the equipment involved. Improper installation, placement or pressure could lead to a boot slipping out while in use and may result in serious injury. It's imperative to be very thorough and careful while installing Salomon ski bindings.

Things You'll Need

  • Skis
  • Ski boots
  • Screwdriver
  • Pen or pencil
  • Drill
  • Epoxy
  • DIN chart
  • Salomon binding instructions
Show More

Instructions

    • 1

      Purchase the correct Salomon ski bindings by familiarizing yourself with your ski equipment, preferred style and techniques. Salomon manufactures bindings for all types of skiing, such as slalom, freestyle, racing and moguls. Understand your own size, speed and style on the slopes before choosing your bindings. Read up on the specifications of bindings before choosing which ones to purchase.

    • 2

      Locate the midsole on the side of the ski. Also called the "sweet spot," the midsole is a mark at the center of the ski, right where the ball of the foot sits. Bindings typically are centered over this mark. More experienced skiers may prefer to adjust their bindings to their personal liking. Placement often depends on the skier's size, speed, style and preferred terrain. Binding installation generally should begin at the midsole mark.

    • 3

      Center the binding over the midsole mark. Place a ski boot so that the toe piece lines with the boot. The center of the boot should be over the midsole mark, then adjusted, if preferred. Fit the boot into the toe piece so that it is snug and aligned straight. Move the boot without disturbing the alignment or the place of the toe piece. Use the pen or pencil to mark spots on the skis through the toe piece screw holes.

    • 4

      Place pilot holes with the toe piece on the spots. Use the drill, but do not push too far into the ski. Patch up leftover holes with epoxy if the ski had a previous pair of bindings. Line up the boot to makes sure it's in the proper placement of the toe piece.

    • 5

      Install the toe piece onto the ski using a screwdriver and the screws that came with the bindings. Tighten the screws enough so that the front of the binding does not move. Do not overtighten, which warps or cracks the ski. Apply a drop of epoxy around the new screws to waterproof the ski.

    • 6

      Place the toe of the boot into the toe binding, and, if possible, adjust the forward pressure of the binding. Refer to the instructions that came with the binding for specific settings and which screws to adjust to reach the needed pressure. The forward pressure is the amount of tension placed on the front of the toe to keep it locked in while in use. Too little pressure could lead to the boot slipping out. Adjust the pressure before placing the binding's heel piece because adjustment to the pressure could lead to slight alterations in the placement of the heel piece. Once the pressure is adjusted, make sure that the boot is absolutely straight, and bring the heel piece tight to the heel of the boot.

    • 7

      Align the boot heel to the heel piece in the same manner as done previously with the toe. Make sure the boot heel is tight to the piece and, along the with the adjusted toe piece, locks the boot in a solid, straight position. Remove the boot without disturbing the heel piece. Place marks in the heel screw holes, drill pilot holes, and screw in the heel piece. Apply epoxy to the the holes as was done with the toe piece.

    • 8

      Lock the boot into the binding, and check that it is secure and ready for use.

    • 9

      Set the binding's tension point, or DIN. DIN settings are based on the skier's size and expertise. Consult a DIN chart or refer to one online if you are unsure of the correct setting. Incorrect DIN settings may result in the boot slipping out while in use.

    • 10

      Follow the same procedure for the other ski.